Pegboard drilling jig — v3 design
V3 is a customizable two-tool system for a square hole grid. The first tool registers on a board corner and drills a 2×2 seed. The second tool has four matching locating pins and a configurable field of drill guides.
The initial cutter profile is for an ordinary twist drill with a metal guide bush. A Forstner or hole-saw profile is a later design step because its wider cutter needs a different clearance and pilot-guide arrangement.
The 10 mm hole, 50 mm pitch, and 25 mm edge offset are starting values carried over from the earlier jig. Check that they match the panel you plan to drill; the edge offset in particular was an assumption in the previous design.
Default design
- Finished holes: 10 mm
- Grid spacing: 50 mm
- First-hole edge offset: 25 mm
- Board thickness: 18 mm
- Corner starter: 2×2 guides
- Indexing tile: 4×4 stations, with 4 removable locating pins + 12 guides
- Printer target: Bambu Lab A1 mini, 180×180×180 mm build volume
- Indexing tile footprint: 170×170 mm at the defaults
The indexing tile's pins occupy the first 2×2 stations. All other stations are
drill guides. At the default 4×4 setting, move it by two grid pitches so the
pins land in four holes from the previous placement. For smaller tiles, the
step is index_cols - 2 pitches across and index_rows - 2 pitches down.
The board grid is extended in overlapping tile regions; a partial final
placement is fine at board edges.
Customizer settings
Edit scad/params.scad or use OpenSCAD's Customizer:
hole_d,grid_pitch, andedge_offsetdefine the board's pattern.board_colsandboard_rowsdescribe the board. Total holes are their product. For equal edge offsets, nominal board width is2 * edge_offset + (board_cols - 1) * grid_pitch; height usesboard_rowsin place ofboard_cols. The jig geometry itself is independent of the board's overall size.bush_idshould match the drill-bit diameter.bush_odandbush_seat_ddescribe the metal bush and its printed press-fit socket.pin_clearancetunes how tightly the locating pins fit the drilled holes;pin_mount_clearancetunes the removable pins' fit in the tile body.index_colsandindex_rowschange the indexing-tile station field. The four pins remain a 2×2 pattern; every other station becomes a guide.build_x,build_y, andbed_edge_clearanceenforce the printer limit. OpenSCAD stops with an assertion if the selected tile does not fit.
For an ordinary twist bit, the default 4×4 layout gives twelve drill guides per placement. Smaller beds or wider grid spacing can require a smaller tile. The default 170 mm footprint leaves 5 mm to each A1 mini bed edge; print the tile without a brim. The design is deliberately kept within the stated bed envelope, but slicer preview should confirm the actual orientation and skirt settings before printing.
Parts and assembly
The corner-starter tool has a flat guide plate and a separate L fence. These
two printed pieces mate through tabs and pockets; dry-fit first, then glue the
joint after checking that the fence sits square. Together they form the first
tool. The indexing tool is a flat-printing body plus four small pin inserts.
indexing_pin_set.scad lays out all four inserts for one print. They press into
the tile from the top face, with the chamfered ends pointing down in use.
preview_corner_starter.scad shows the assembled starter; export its plate
and fence as separate STLs.
preview_indexing_tile.scad shows the indexing body with its four pins
installed; export the body and pin set separately.
Print the starter plate flat with the bosses up. Print the fence standing on its two long bottom edges; a brim may help. Print the indexing body flat with the guide bosses up. Print the pin set with the four heads on the bed.
- Glue the starter's fence square to its plate, then set it against both board edges and clamp it.
- Drill four seed holes through its bushes.
- Fit the four pin inserts into the indexing body.
- Remove the starter, seat the indexing pins in the seed holes, clamp the tile on its open perimeter rails, and drill the twelve guide positions.
- Leapfrog by the configured tile step, using four finished holes as references. At the default 4×4 setting, the step is two rows or columns.
Use metal drill bushes. The plastic seats are tunable press fits, not a
substitute for a hardened guide. Print a small fit coupon before the full
tools. Tune bush_seat_d and pin_clearance to the filament, printer, and
actual hardware.
Export
From the project folder:
openscad -o stl/corner_starter_plate.stl scad/corner_starter_plate.scad
openscad -o stl/corner_starter_fence.stl scad/corner_starter_fence.scad
openscad -o stl/indexing_tile.stl scad/indexing_tile.scad
openscad -o stl/indexing_pin_set.stl scad/indexing_pin_set.scad
This is the first parametric design pass. The next design checks are the tab fit, bush-seat fit, pin fit, index-tile clamping access, and a scrap-board alignment run before relying on it for a full panel.
Web configurator and case study
Open index.html to configure a board pattern, view the 3D tools, and step
through the corner-seed and tile-indexing sequence. The configurator reports
the board hole count and nominal size, limits the tile layout to the A1 mini
bed, and downloads the selected settings as JSON. It uses Three.js from a CDN,
so serve the folder over HTTP instead of opening it with a file:// URL:
cd pegboard-jigs-v3
python3 -m http.server 8000
Then open http://localhost:8000. See CASE_STUDY.md for the
design rationale, formulas, workflow, and validation status.
The browser tool previews configurations and exports their settings. The
included STL files are the default 10 mm / 50 mm / 25 mm profile. To generate
custom print geometry, update scad/params.scad and export the OpenSCAD parts.
Deeper dive
V3 pegboard jig — case study
Problem
Drilling a large, evenly spaced hole grid into a plywood panel requires a repeatable reference. Measuring every hole is slow, and small placement errors can accumulate. V3 uses a corner reference once, then carries that reference forward through the holes already drilled.
Design goal
Build a configurable two-tool system that:
- starts from a panel corner and drills a matching 2×2 seed;
- registers the indexing tool with four pins in those four seed holes;
- drills as many new holes per placement as the A1 mini can print in one rigid tile;
- supports an ordinary twist drill guided by a metal bush;
- exposes board, cutter, fit, and tile settings in a browser configurator.
The wider-cutter profile for Forstner bits and hole saws is a later step. Those cutters need a guide for the pilot and a separate opening for the wide cutting head.
System
1. Corner starter
The corner starter uses an L-shaped fence to register against both panel edges. Four guide bushes sit on the selected square grid positions:
● ●
● ●
At the default 50 mm pitch and 25 mm edge offset, the seed centres are at (25,25), (75,25), (25,75), and (75,75) mm from the panel corner. The fence is printed separately from the flat guide plate and glued square after a dry fit.
2. Four-pin indexing tile
The tile repeats the same 2×2 locator pattern in its first four stations. Every other station in the configured tile is a guide. The default 4×4 layout is:
P P G G
P P G G
G G G G
G G G G
P marks a locating pin; G marks a drill guide. The layout yields twelve
new guide positions per full placement. Four removable pins are used so the
large tile body can print flat with its guide bosses up.
The tile advances by the overlap that remains after reserving its 2×2 pin
field: tile columns - 2 grid steps horizontally and tile rows - 2 steps
vertically. At the default 4×4 setting, that is two pitches in either
direction. Each next placement lands its four pins in holes from the prior
placement.
Customization model
The web tool at index.html exposes:
- board hole count across and down;
- finished hole / drill-bit diameter;
- centre-to-centre pitch and first-hole edge offset;
- panel thickness;
- tile station rows and columns, constrained by the printer bed;
- bush dimensions, printed bush-seat diameter, and pin clearance.
The board hole count is columns × rows. With equal edge offsets, nominal
panel width is:
2 × edge offset + (columns - 1) × pitch
Nominal panel height uses rows in place of columns. The guide count is:
tile columns × tile rows - 4 locating pins
The body envelope is estimated as (stations - 1) × pitch + boss diameter.
At 10 mm holes, 50 mm pitch, and 20 mm guide bosses, a 4×4 tile is 170×170 mm.
A 5×5 tile would exceed the A1 mini's 180×180 mm build area at this pitch.
Smaller pitches may allow more stations, provided the guide bosses retain
enough material between them.
Drilling workflow
- Set the corner starter's L fence against both panel edges and clamp it.
- Drill the four seed holes through the metal guide bushes.
- Fit the four locating pins into the indexing body.
- Remove the starter. Seat the indexing pins in all four seed holes and clamp the tile to the panel.
- Drill through each highlighted guide position.
- Lift and move the tile by its configured overlap step. Seat all four pins in finished holes before drilling again.
- Repeat the tile placements across the board. A partial final tile handles the outer rows and columns.
The browser walkthrough builds this placement sequence from board and tile settings, highlights the current guide positions, and reports how many holes are covered by the plan.
Print and fit decisions
- Printer envelope: Bambu Lab A1 mini, 180×180×180 mm.
- Default indexing body: 170×170×14 mm; 5 mm nominal bed-edge margin.
- Starter plate: 115×115×14 mm; fence: 119×119×26 mm.
- Four pin inserts print as a separate set, 68×14×17.6 mm in the default arrangement.
- A metal 12 mm OD / 10 mm ID bush is the default twist-drill guide.
- The printed bush seat and pin sockets remain adjustable for the actual filament, printer, and purchased bush.
The browser configurator updates the demonstration model and downloads a JSON settings summary. The bundled STL files are the default profile; custom print geometry comes from the parametric OpenSCAD sources.
Validation and next work
OpenSCAD generated the current default STL files as manifold solids. That checks the model construction, not the real printed fits or drilling accuracy. The first physical prototype should check the bush seat, pin fit, fence alignment, and clamp access, followed by an alignment run on scrap plywood. Those measurements can then tune the shared parameters.
The next cutter profile should treat a Forstner bit or hole saw as a separate guide system: guide the centre pilot while leaving clearance for the larger cutting head. The twist-drill profile remains the initial v3 scope.